Walbro In-tank Fuel Pump Accessories
If you can't find your vehicle on the application chart of the intank page, take a look at these parts. Maybe you can find something you can use.
The GSSxxx Walbro pumps don't have simple terminal lugs for power connections. Walbro makes a special snap-in connector that plugs into the pump. A significant number of vehicles will plug right into the pump, but some don't. A 12-inch wiring pigtail w/ two fuel-resistant butt connectors is $5.00.
A 42-inch wiring pigtail w/ two fuel-resistant butt connectors is $6.00.
Or take the DIY approach and buy the pieces to crimp onto your own wires. Parts include the plastic shell, the retainer, and two terminals. Each kit is $2.00. some assembly required
Some kits come with a foam sleeve to help isolate the pump and keep it from flopping around. The GSSxxx pumps are 39 mm in diameter. To make the pump larger, so it will fit in certain holders, or to dampen some of the noise, you can put the pump in a foam sleeve.
| Part | Description | Price |
| Thin | Makes pump/sleeve diamter about 44 mm | $1.00 |
| Medium | Makes pump/sleeve diameter about 48 mm | $2.00 |
| Thick | Makes pump/sleeve diameter about 55 mm NOT foam - solid neoprene |
$3.00 |
Many newer applications have a pump module with a flex hose in it. About the only way to get a pump in the module is to destroy the flex hose. Have no fear; We have several corrugated, flex hoses to choose from. These have been approved for gasoline, diesel, and E85. They are rated at a burst pressure over 300 psi.
| End ID | Length | Price |
|---|---|---|
| 8 mm on each end | 136 mm [5.35 in] |
$3.25 |
| 8 mm on each end | 160 mm [6.30 in] |
$3.50 |
| 8 mm on each end | 172 mm [6.77 in] |
$3.75 |
| 8 mm on each end | 188 mm [7.40 in] |
$4.00 |
| 8 mm on each end | 225 mm [8.86 in] |
$4.25 |
| 8 mm on each end | 236 mm [9.29 in] |
$4.50 |
| 8 mm on each end | 275 mm [10.83 in] |
$4.75 |
| 8 mm on each end | 284 mm [11.18 in] |
$5.00 |
| 8 mm on each end | 350 mm [13.78 in] |
$5.25 |
| 8 mm on each end | 380 mm [14.96 in] |
$5.50 |
| End ID | Length | Price |
|---|---|---|
| 10 mm on each end straight tube; not corrugated |
50 mm [1.97 in] |
$4.00 |
| 10 mm on each end | 80 mm [3.15 in] |
$4.00 |
| 10 mm on each end | 120 mm [4.72 in] |
$4.25 |
| 10 mm on each end | 160 mm [6.30 in] |
$4.50 |
| 10 mm on each end | 180 mm [7.09 in] |
$4.75 |
| 10 mm on each end | 220 mm [8.66 in] |
$5.00 |
| 10 mm on each end | 240 mm [9.45 in] |
$5.50 |
| End ID | Length | Price |
|---|---|---|
| 8 mm on one end 10 mm on one end |
120 mm [4.72 in] |
$5.50 |
If you need to put a piece of high pressure hose in your fuel tank, be sure it's rated for in-tank use. Your typical parts store high pressure EFI hose is only rated for outside the tank use [SAE J30R9]. That hose will turn to mush in no time. A six-inch piece of 5/16 high-pressure, in-tank hose made to Chrysler specs [not-quite-J30R10 spec] is $3.00.
If you need honest-to-goodness SAE J30R10 hose, that's gonna cost you a bit more. Your typical parts store will probably only have 1-ft pieces. We can cut you any length you want. The 5/16 ID J30R10 hose is $20.00 per foot or $1.75 per inch if you need less.
The 3/8 ID J30R10 hose is $20.00 per foot or $1.75 per inch if you need less.
You'll probably need a couple hose clamps if you get the J30R10 hose or the flex hose. We have some in case you don't want to bother with running down to the hardware store. These stainless #4 hose clamps are $0.60 each.
If you put the GSS242, GSS307, or GSS340 in a custom application you're going to need a pickup filter. If one of the kits below doesn't have a filter that will work, here is a small, flat pickup filter that's only 4 inches long and 2.25 inches wide. These filters are $4.00 each.
This is the same filter as the one in the Mustang kit (Kit26). It's 5.25 inches long and 2.25 inches wide. These filters are $6.00 each.
Here's a pickup filter for the F20000169 pump. It is 4 inches long and 1.625 inches wide. These filters are $5.00 each.
Here's a pickup filter for the 516 pump. This is also the filter that was used on the GSS340M pumps. It is 4 inches long and 1.75 inches wide. These filters are $6.00 each.
If you need a pickup filter for a GSS250, GSS278, GSS315, GSS317, GSS341 or GSS342, we carry a few.
| Part | Description | Price |
| Tiny | Pickup filter that is 2.25 inches wide by 2.625 inches long | $6.00 |
| Short | Pickup filter that is 2.25 inches wide by 3.25 inches long | $8.00 |
| Long | Pickup filter that is 2.25 inches wide by 4.50 inches long | $8.00 |
Walbro Fuel Pump Kits
The following kits will fit the following pumps:
- GSS250 & GSS278 [190 ltr/hr pumps]
- F2000141 [high pressure 190 ltr/hr pump]
- GSS315 & GSS317 [255 ltr/hr pumps]
- GSS341 & GSS342 [high pressure 255 ltr/hr pumps]
 Kit 1 - $30.00 |  Kit 2 - $15.00 |
 Kit 3 - $20.00 |  Kit 4 - $25.00 |
 Kit 5 - $26.00 |  Kit 6 - $21.00 |
 Kit 7 - $21.00 |  Kit 8 - $24.00 |
 Kit 9 - $21.00 |  Kit 10 - $14.00 |
 Kit 11 - $19.00 |  Kit 12 - $20.00 |
 Kit 13 - $23.00 |  Kit 14 - $25.00 |
 Kit 15 - $26.00 |  Kit 16 - $21.00 |
 Kit 17 - $17.00 |  Kit 18 - $27.00 |
 Kit 19 - $29.00 |  Kit 20 - $27.00 |
 Kit 21 - $31.00 |  Kit 22 - $24.00 |
 Kit 23 - $18.00 |  Kit 24 - $17.00 |
 Kit 25 - $17.00 |  Kit 34 - $19.00 |
 Kit 36 - $23.00 |
The following kits will fit the following pumps:
- GSS242 [190 ltr/hr pump]
- GSS307 [255 ltr/hr pump]
- GSS340 [high pressure 255 ltr/hr pump]
 Kit 26 - $21.00 |  Kit 28 - $41.00 |
 Kit 29 - $18.00 |  Kit 30 - $19.00 |
 Kit 31 - $19.00 |  Kit 32 - $12.00 |
 Kit 33 - $-- |  Kit 37 - $18.00 |
The following kits will fit the following pumps:
- F20000169 [high pressure 255 ltr/hr pumps]
 Kit 27 - $19.00 |
Please read our Policies
© copyright 1999-2024 Auto Performance Engineering